CASTI Guidebook ASME B Process Piping CASTI Publishing Inc. – Street Edmonton, Alberta T5H 3J7 Canada Tel:() Fax:(). CASTI Guidebook to Asme B has 1 rating and 0 reviews: CD-ROM. CASTI Guide to Asme B – Process Piping (The Practical Guide Book Series) By Glynn E. Woods, Roy B. Baguley.
|Published (Last):||7 October 2009|
|PDF File Size:||5.46 Mb|
|ePub File Size:||11.64 Mb|
|Price:||Free* [*Free Regsitration Required]|
This standard also has a minimum pressure requirement. The Code does not address high cycle – low stress piping life in vibrating systems. SE a secondary stress will be discussed in the Displacement Stress Range section of this xasti. To do so, each book must have a valuable topic, be current with today’s technology, and be written in such a manner that gudebook reader considers the book to be a reliable source of practical answers that can be used on a regular basis.
CASTI Guidebook to ASME B31.3 – Process
This book includes supplementary information that the Code does not specifically address. A substantial amount of additional detail may be necessary to completely engineer and construct a process piping system, depending upon the piping scope and complexity. Overstrain of piping components, Overstrain of supporting structures, Leakage at joints, and Overstrain of connecting equipment, without material waste. A vibrating piping system see Figure 2.
For example, a weld could be examined by the ultrasonic method using a shear wave technique, where the sound beam propagates in a shear wave mode. Plant casto issues center on the effect of an unplanned shutdown. The boilers of these early steam engines were little more than tea kettle type arrangement where direct heating of the boiler wall was the method used to generate the steam.
These requirements as well as the definition and Code responsibilities for Category M Fluid Service are the subject of this chapter. Pressure Design of Piping Components Wall Thickness for Straight Pipe under Internal Pressure The most xasti deviation from the base Fasti is in the equations for determining the wall thickness requirements for internal pressure.
Those that can be judged adequate by comparison with previously analyzed systems, and 3. And, for dimension critical applications, as an alternative to specification of tangent lengths, one could consider specifying center to end dimensions i. There are endless cross references to explore during problem solving and the subject matter often overlaps several technical disciplines.
Principal Axis and Stress The analysis of piping loaded by pressure, weight, and thermal expansion can appear to be rather complicated and difficult to accomplish.
In high pressure piping, this Code compliance shall be presented in the form of a written report, summarizing the results of the design analysis and the designer shall certify compliance with the B Loss of power to homes on a cold winter night is an example of a reason to have very high plant reliability in B In a yuidebook system, the stress concern is high cycle, azme stress.
CASTI Guidebook to Asme B31.3: Process Piping
The guidebok stress for pressure design is Sh, the basic allowable stress of the material at the hot temperature. Exposure by breathing or bodily contact to even a very small quantity of such fluid, caused by leakage, can produce serious irreversible harm to persons even when prompt restorative measures are taken. Weld examination requirements for gaging the structural integrity of welds. Another graph covering that stress and cycle range would have to be selected to address cycle life of that lower stress range.
Rather, the user should be looking at more global issues including resistance of generic material groups to various forms of corrosion, material cost and availability for various product forms, delivery times, need for qualification testing, and existence of suitable forming and joining technology.
The designer must determine the mill under-run tolerance for the manufacturing process and add that tolerance to the tm value before making the purchase. The stress limit of the yield strength at temperature is simply a restatement of the maximum principal stress failure theory.
Their transportation home was aboard the Mississippi River steamboat Sultana Figure 1. Cogeneration plants within a refinery, for example, could be designed either to B The key components of the design conditions guidebooj the design pressure and the design temperature.
Definition The definition of gujdebook Category M Fluid Service is a fluid service in which the potential for personnel exposure to toxic fluids is judged to be significant. It is the opinion of the Committee that until such time as an ASA Pressure Piping Code Section specifically applying to chemical process piping has been published, chemical process piping may be designed, fabricated, inspected, and tested in accordance with the requirements of ASA B Flange rating procedures will be discussed later in this chapter.
With these three design conditions known, the owner will have sufficient information for deciding whether or not to impose high pressure piping requirements. With the above in mind, it might be assumed that the B In fact, such designers who are capable of applying a more rigorous analysis have the latitude to do so provided they can demonstrate the validity of their approach.
We would like to hear from you. What are the standards of acceptance applicable to each examination? Continuing to study the conditions for pressure-temperature variations, we find one of the most misinterpreted and misapplied statements of the Code. It too was dissolved and the rules developed for b31.3 piping were incorporated into the aame of B He is also a certified CGSB technician tto Level II radiographic, ultrasonic, magnetic particle, and liquid penetrant nondestructive test methods.
CASTI Guidebook to ASME B – Process
The sum of the longitudinal stresses due to pressure, weight, and other sustained loadings plus stresses produced by occasional loads, such as wind or earthquake, guidebooi be as high as 1. Hot bending is carried out in the bright red heat range where the metal is austenitic in structure.
However, changes to direction of flow may also be made through the use of pipe bends. Design temperature method of determination other than fluid temperature is permitted provided this temperature is established by heat transfer calculation procedures consistent with industry practice.
The f factor although appropriate for the 18, cycles of this problem, is also suitable for 22, cycles as shown in Table Their values are found in B