HT12D is a series decoder IC for remote control applications manufactured by Holtek. It is commonly used for radio frequency (RF) applications. Download. RF transmitter and RF receiver of Mhz; 3 push buttons; IC HT12D; IC HT12E; Hearders (male or female it doesn’t care); 3 resistors with a value from ( to. HT12D is a decoder integrated circuit that belongs to series of decoders. This series of decoders are mainly used for remote control system applications, like.
| Author: | Dajar Digul |
| Country: | Albania |
| Language: | English (Spanish) |
| Genre: | Travel |
| Published (Last): | 17 May 2018 |
| Pages: | 354 |
| PDF File Size: | 7.62 Mb |
| ePub File Size: | 16.92 Mb |
| ISBN: | 915-2-35475-777-3 |
| Downloads: | 67854 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Meztirn |
This pin powers the IC should use only 5V. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. The data on 4 bit latch type output pins remain unchanged until new is received. This series of decoders are mainly used ht1d2 remote control system applications, like burglar alarm, car door controller, security system etc.
The serial input data is compared with the local addresses three times continuously. These are the 8-bit address bits, which is used to protect your data.
So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you.
What is Web Browser. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. If any valid data is received they can be obtained from these four pins.
Interface GPS with Arduino. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.
It is very important that your Decoder should have the same address of that of the encoder. This high-density System-in-Package SiP integrates controller, power switches, and support components.
A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.
HT12D Decoder IC
It is not mandatory to use it. The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be hy12d using the pins A0 to A7. They are paired with 2 12 series of encoders. Valid transmission; active high. Skip to main content.
HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. Choosing Motor For Robots. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output h12d pins.
This pin will go high when a data is received. This oscillator can be used by connecting these two pins through a 1M Resistor. A valid transmission in indicated by a high signal at VT pin.
HT12D Decoder IC | HT12D Datasheet | Pin Diagram
To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here. In simple terms, HT12D converts the serial input kc parallel outputs.
It is mainly provided to interface RF and infrared circuits. Virgin Galactic — Commercial Space Flight. Submitted by admin on 27 October Supply voltage; 5V 2. The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded.
HT12D RF Decoder IC Pinout, Details, Equivalent & Datasheet
Jc you want security you can connect any of the 8 pins to 5V to make it high. We should set the bits in same pattern on Encoder and Decoder IC to pair them. They can also be connected to LED to physically view the received data. Choosing Battery for Robots. HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders.